Free IL-ROOF Practice Questions

Question 1

Paint is peeling and wall sheathing is soft immediately below the lower end of a roof-to-sidewall intersection. During rain, runoff follows the step flashing but passes behind the siding before reaching the gutter. The upper flashing laps are intact, and the gutter drains freely. Which repair addresses the observed water-entry path?

Accepted Answer

Install kick-out flashing integrated with the wall drainage plane and discharging into the gutter.

Answer

Extend the existing step flashing farther up the roof-to-sidewall intersection.

Answer

Seal the bottom edge of the siding continuously to the adjacent roof shingles.

Answer

Replace the eave shingles and increase their overhang into the existing gutter.

Question 2

A crew is hand-applying membrane on a 70-foot-wide, 3:12 roof with edges 18 feet above grade. A compliant warning line surrounds the work area 8 feet from the edges. A competent safety monitor stays on the roof, can see and speak with the workers, and has no distracting duties. No mechanical equipment is used. Under OSHA, which assessment of this edge-fall-protection arrangement is correct?

Accepted Answer

The warning line and safety monitor are a permitted combination for this roofing operation.

Answer

Roofing must be suspended until guardrails or personal fall-arrest systems are provided.

Answer

The warning line can be removed because monitoring alone is permitted on any low-slope roof.

Answer

The monitor can be reassigned because an 8-foot warning-line setback is sufficient by itself.

Question 3

The entire horizontal projection of a gable roof, including overhangs, measures 48 by 32 feet. Both roof planes have a 9:12 slope; the corresponding area factor is 1.25. The selected field shingles cover 100 square feet per three bundles. Allow 10% cutting waste; starter and ridge materials are ordered separately. How many whole bundles of field shingles should be ordered?

Accepted Answer

64 bundles

Answer

51 bundles

Answer

58 bundles

Answer

127 bundles

Question 4

After wind and air temperature change, a crew makes a new TPO trial weld on clean, dry membrane. Once cooled, the sample peels apart cleanly at the welded interface rather than tearing the sheet. The welder still displays the setting used successfully that morning. What should the foreman do with this result?

Accepted Answer

Adjust the settings for current conditions until a cooled trial weld passes evaluation.

Answer

Keep the settings and increase the amount of sheet overlap before welding.

Answer

Continue welding and reinforce the completed seams with edge sealant later.

Answer

Retain the settings because the clean membrane rules out a preparation problem.

Question 5

An Illinois contractor with a Limited Roofing License is asked to reroof one 12-unit apartment building. The owner proposes two contracts, each covering the roof above six units, with the work performed in separate phases. Which licensing conclusion is correct?

Accepted Answer

An Unlimited license is required; splitting the work does not change the property size.

Answer

The Limited license is sufficient because the building is used entirely for housing.

Answer

The Limited license is sufficient if each contract and work phase covers only six units.

Answer

The Limited license is sufficient if the roofing material is also used on single-family homes.

Question 6

An owner reports ceiling drips when mild weather follows a cold spell, even without rain or snow. A cold-morning inspection finds frost beneath sound roof sheathing measuring 28 degrees F; the attic air has a dew point of 43 degrees F. Ceiling penetrations leak indoor air, but soffit-to-ridge ventilation paths are clear. Which intervention targets the moisture mechanism?

Accepted Answer

Air-seal the ceiling penetrations while preserving the ventilation paths.

Answer

Enlarge the ridge exhaust openings without changing the ceiling air leaks.

Answer

Install a full-deck ice-barrier membrane beneath the existing field shingles.

Answer

Replace the roof covering above every room that developed a ceiling stain.

Question 7

During a hot afternoon, a roofer becomes confused, staggers, and cannot answer simple questions. The worker is still sweating heavily. Coworkers have moved the worker safely to a shaded, protected area. What is the immediate priority?

Accepted Answer

Call 911 and begin rapid cooling while someone remains with the worker.

Answer

Give an electrolyte drink and reassess after a supervised 15-minute rest.

Answer

Have a coworker drive the worker to a clinic after the worker feels steadier.

Answer

Call 911 and keep the worker resting without cooling until responders arrive.

Question 8

A double-lap slate roof will use 22-inch-long slates. The approved layout requires at least 4 inches of headlap, but the installer has marked a 10-inch course exposure. To correct the layout without using more courses than necessary, what should the maximum exposure be?

Accepted Answer

9 inches

Answer

7 inches

Answer

11 inches

Answer

18 inches

Question 9

Stronger deck screws are proposed after an uplift test of a fully adhered commercial roof fails. In the specimen, the membrane and adhesive remain bonded to a facer torn from its foam core; the insulation plates and deck fasteners remain secure. Select the change that addresses the actual failure mechanism.

Accepted Answer

Select a tested assembly with adequate facer-to-core strength and matching components.

Answer

Use deck screws with greater pullout resistance in the existing steel deck.

Answer

Install a thicker reinforced membrane over the same insulation and facer.

Answer

Increase membrane adhesive coverage on the existing insulation facer.

Question 10

A porch roof has a 3:12 slope and sound plywood decking. For a conventional asphalt-shingle installation, which proposal properly addresses the underlayment requirement associated with this pitch?

Accepted Answer

Use double-coverage underlayment or an approved equivalent assembly.

Answer

Use ordinary single-coverage felt and increase the number of nails per shingle.

Answer

Use ordinary single-coverage felt and cement the exposed shingle joints.

Answer

Reject asphalt shingles because every roof below 4:12 requires a membrane covering.

Free IL-ROOF Practice Questions

Domain 1: Safety & Employee Protection

Question 1

Question 2

Domain 2: Roofing Preparation & Materials

Question 3

Question 4

Domain 3: Steep-Slope Roofing Systems

Question 5

Question 6

Question 7

Domain 4: Low-Slope Roofing Systems

Question 8

Domain 5: Rules, Regulations & Business Practices

Question 9

Domain 6: Non-Residential Roofing Systems

Question 10

That's 10 of 1,030